FGF941CH
Part of Flotrex™ GF Pleated Filters with Glass Microfiber Media
The Flotrex GF (FGF) filter (Figure 1) is an absolute rated, glass microfiber filter that is dependable and very efficient in the removal of Cryptosporidium and Giardia cysts.
Literature
Specifications
- Absolute Micron Rating
- 0.45 µm
- Elastomer Material
- Silicone, Viton, Buna-N, EPDM
- End #1 Adapter
- 213 O-Ring
- End #2 Adapter
- Fin Adapter
- Filter Model
- FGF94
- Nominal Cartridge Length
- 25 cm / 10 in
Note
Trademark of General Electric Company; may be registered in one or more countries
Applications
Flotrex GF filters are specifically designed for high throughput and long service life. Typical applications include:
- Final Filtration for Bottled Water
- Prefiltration of Pharmaceuticals and Biologicals
- Cosmetic Oil, Gel and Shampoo Filtration
- Beverage Clarification
- Paints and Coatings
- Ink
General Properties
Flotrex GF filters are available the following absolute pore size micron ratings: 0.45 and 3.0 µm and 1.0 um which is NSF Standard 53 certified. Tables 1, 2, 3 and 4 show further details on materials of construction, dimensions, operational limits and flow performance in air and water.
Additional Information
- Flotrex GF filters may be autoclaved or in situ steam sterilized (up to 257°F [125°C] 30-minute cycles) for a maximum accumulated exposure of 10 hours. Alternatively, the filters may be sanitized with compatible chemical agents.
- GE certifies that the materials contained in its Flotrex GF pleated filters meet US FDA requirements for food contact under the applicable regulations in 21 CFR. For further information, contact GE technical services. Flotrex GF filters meet the test criteria for USP Class VI-121°C Plastics.
- Aqueous extracts from Flotrex GF filters contain less than 0.25 EU/ml. The filters typically exhibit low levels of non-volatile residues.
- GE Filter cartridges are designed and manufactured for resistance to a wide range of chemical solutions. Conditions will vary with each application and users should carefully verify chemical compatibility. Please contact your GE distributor for more information.
The Flotrex-GF 1.0 micron filter has been tested according to ANSI/NSF Standard 53 for reduction of the substances listed below. The concentration of the indicated substances entering the filter was reduced to a concentration less than or equal to the permissible limits for leaving the filter, as specified in ANSI/NSF Standard 53. Testing was performed under standard laboratory conditions. Actual performance may vary. Table 5 shows ANSI/NSF Standard 53 standards used in the performance testing.
Line Specifications
- Core and Cage
- Polypropylene
- Effective Filtration Area
- 4 ft² / 0 m²
- Endcaps and Adapters
- Polypropylene
- Filtration Media
- Acrylic Resin-Bonded Glass Microfiber
- Influent Challenge Concentration
- Minimum 50000/L
- Maximum Forward Differential Pressure @ 70°F (21°C)
- 4.1 bar / 60 psi
- Maximum Operating Temperature at 10 psid (0.69 bar) in Water
- 82 °C / 180 °F
- Maximum Reverse Differential Pressure @ 70°F (21°C)
- 2.1 bar / 30 psi
- Nominal Inside Diameter
- 1.25 in / 31 mm
- Nominal Outside Diameter
- 2.75 in / 70 mm
- Reduction Requirement
- 99.95%
- Substance
- Cyst
- Support Layers
- Polypropylene Microfiber
- Type
- FGF
See more parts in Flotrex™ GF Pleated Filters with Glass Microfiber Media
Request a Quote
This part number is already on the request. Tell us how many you need and our specialists will come back to you.